The essential health and safety requirements (EHS) are the mandatory provisions set out in Annex III to Regulation (EU) 2023/1230 that a machine must meet in order to ensure a high level of protection of the health and safety of persons and, where applicable, of domestic animals, property and the environment due to the hazards it presents. The regulation, applicable from January 20, 2027, defines them in its Article 3, point 14; a machine may not be made available on the market or put into service unless it complies with them (Article 8).

In short

  • They target the manufacturer and the design of the machine, not the organization of work at the user’s place.
  • They are formulated as objectives to be achieved; the harmonized standards describe a way to achieve them and provide a presumption of conformity.
  • A requirement applies only if the corresponding danger exists, except for three blocks that always apply: the principles of safety integration, machine marking, and the instruction manual.
  • It is the risk assessment that determines which ones apply to a given machine; the technical documentation keeps a list of them.

What the text says

Regulation (EU) 2023/1230 defines the essential health and safety requirements as «the mandatory provisions, set out in Annex III, relating to the design and construction of products within the scope of this Regulation in order to ensure a high level of protection of the health and safety of persons and, where applicable, of domestic animals and property, and, where appropriate, of the environment» (Article 3, point 14).

Three articles draw the obligations:

  • Article 8 Machines and related products are only made available on the market or put into service if, «installed and properly maintained and used in accordance with their normal use or under reasonably foreseeable conditions, they meet the essential health and safety requirements set out in Annex III». Quasi-machines must meet the «relevant» requirements;
  • Article 10 The manufacturer ensures that the machine or related product «has been designed and manufactured in accordance with» these requirements, establishes the technical documentation and implements the applicable conformity assessment procedure;
  • Article 11 : the same obligation applies to the manufacturer of a quasi-machine, limited to the relevant requirements.

The general principles of Annex III (Part B) set out how they should be applied: the manufacturer has a risk assessment carried out «in order to determine the essential health and safety requirements that apply», then designs and builds the machine to eliminate the hazards or reduce the risks (point 1).

How is Annex III organized?

OPTIMA.ai solution: machine security lexicon | essential requirements and annexes.
Annex III: definitions, principles, a chapter common to all machines and five additional chapters.
  • Part A, definitions, including: danger, dangerous area, operator, risk, protector, protective device, normal use, reasonably foreseeable misuse.
  • Part B, general principles : the risk assessment and its stages, and the rules for applying the requirements.
  • Chapter 1, applicable to all machinery: general remarks (1.1), principles of safety integration (1.2), control systems (1.3), protection against mechanical hazards (1.4), characteristics of guards and protective devices (1.5), risks due to other causes (1.5), maintenance (1.6), information (1.7, including marking and instructions for use).
  • Chapters 2 to 6, These are «essential additional requirements» for certain categories of machinery (including the food, cosmetics and pharmaceutical industries, portable machines, wood-processing machines), for risks due to mobility, lifting operations, underground work and lifting people.

The text warns: «However, it is imperative to examine the entirety of this annex in order to ensure compliance with all relevant essential health and safety requirements» (part B, point 4).

Do all the requirements apply to all machines?

No. The obligations provided for by an essential requirement «apply only when the corresponding danger exists for the machinery or related product when used under the conditions stipulated by the manufacturer or in foreseeable abnormal situations» (Part B, point 2). A machine without pressurized fluid is not required to meet the requirements related to it.

However, three blocks apply «in all cases»: the principles of safety integration (section 1.1.2), machine marking (section 1.7.3) and the instruction manual (section 1.7.4).

The requirements are mandatory, but the text takes into account the state of the art: if their objectives cannot be achieved, the machine is, «as far as possible, designed and constructed to aim towards those objectives» (Part B, point 3).

How does the manufacturer prove that they comply with them?

The essential requirements set a result, not a technical solution. The manufacturer has several means of demonstrating this:

  • the harmonized standards A machine that complies with harmonized standards whose references are published in the Official Journal of the European Union is «presumed to comply» with the requirements covered by those standards (Article 20, paragraph 1);
  • the common specifications that the Commission may adopt when harmonized standards are lacking (Article 20, paragraph 3);
  • other technical specifications, to be described then in the technical documentation.

The technical documentation contains the risk assessment with «a list of the essential health and safety requirements applicable», the description of the protective measures taken to comply with them, the standards or specifications applied, and the results of calculations, tests and examinations (Annex IV, Part A). Then comes the conformity assessment procedure (Article 25), the EU declaration of conformity (Article 21) and the CE marking (Article 24).

What changes with artificial intelligence

Regulation (EU) 2023/1230 already incorporates machines whose behavior evolves: the risk assessment includes foreseeable hazards «as a predicted evolution of their behavior or of their completely or partially evolving logic» due to different levels of autonomy (Annex III, Part B, point 1).

Regulation (EU) 2026/1744 of 8 July 2026 («Digital omnibus measure on AI») added a new mechanism to Article 8: «The Commission adopts delegated acts» to amend Annex III «by adding health and safety requirements» for high-risk AI systems under Regulation (EU) 2024/1689, because they are components of a machine’s safety or because they are a machine themselves. These delegated acts «shall be applicable on 2 August 2028 at the latest». As of 13 November 2026, none of these delegated acts have been published.

What this changes for the manufacturer, integrator and operator

For the manufacturer

The essential requirements are the reading grid for the entire design. For each requirement of Chapter 1 and the additional useful chapters, the manufacturer decides whether to apply it or not, and why; if so, by what measure and with what evidence. A requirement that is rejected without justification is a weakness in the dossier.

For the integrator

The person who manufactures a set of machines and markets them under his own name, or puts them into service for his own use, is the manufacturer within the meaning of the regulation (Article 3, point 18). He/She takes over the requirements for the set, starting from the declarations of incorporation of the quasi-machines, which specify which essential requirements «are applied and fulfilled» (Annex V, Part B).

For the operator

The essential requirements do not apply to the employer as a user, unless he is building a machine for his own use: in that case he is the manufacturer (Article 3, point 18). The employer must keep his equipment «in a state of conformity with the technical rules of design and construction applicable at the time of its commissioning in the establishment, including with regard to the instructions for use» (Labour Code, Article R4322-1). If he provides a machine with substantial modification, As a manufacturer, it is subject to the obligations of Article 10 for the modified machine (Article 18).

An example

A manufacturer designs a bale press for cardboard. His risk assessment leads him to include, among other things, requirements regarding the control systems and the’emergency stop (1.2), mechanical crushing hazards (1.3), mobile guards with locking device (1.4), hydraulic energy (1.5), separation of the machine from its energy sources (1.6.3), marking and instructions (1.7). The requirements for mobile machines (Chapter 3) or lifting (Chapter 4) do not apply: he writes this, with reason. For each requirement he notes the measure taken and the standard applied. This example is fictitious and simplified.

Common mistakes

  • Contenting oneself with applying a standard without verifying that all applicable requirements are covered: a standard may only cover part of them, and the presumption only applies to those parts.
  • Rejecting a requirement without saying so The technical documentation must list the applicable requirements; a requirement that is ignored is not an «unapplicable» requirement.
  • Forgetting the three blocks that always apply : integration of security, marking, instruction manual.
  • Confusing with the employer’s obligations : a single risk assessment document does not meet the essential requirements.

Essential requirements and employer's safety obligation: what is the difference?

The two expressions are similar, but do not refer to the same person or the same moment. The essential health and safety requirements apply to the manufacturer, at the stage of design and placing the machine on the market (Regulation 2023/1230, Annex III). The employer’s safety obligation falls under the Labour Code: it «takes the necessary measures to ensure the safety and protect the physical and mental health of workers» (Article L4121-1) and provides them with appropriate work equipment (Article R4321-1). The employer relies on what the manufacturer has done, but remains obliged, under its safety obligation (Article L4121-1), to make available «appropriate work equipment» (Article R4321-1) and to assess the risks of their use in its establishment.

Directive 2006/42/EC, which applies until 19 January 2027, already used the same concept in its Annex I, «Essential health and safety requirements relating to the design and construction of machinery»; Regulation 2023/1230 repeats it in its Annex III and completes it.

Related words: Intrinsic prevention, quasi-machine, residual risk, risk assessment (see our article Machine risk analysis according to ISO 12100), CE marking (see CE marking of a machine).

Frequently asked questions

Where can I find the list of essential health and safety requirements?

In Annex III to Regulation (EU) 2023/1230, published free of charge on EUR-Lex. Until 19 January 2027, Annex I of Directive 2006/42/EC applies.

What does «EESS» mean?

This is the common abbreviation for ’essential health and safety requirements«. The regulation uses the expression verbatim.

Is a harmonized standard mandatory?

No. The manufacturer may apply other technical specifications, provided that he demonstrates in the technical documentation that he meets the applicable essential requirements. The harmonized standard only provides him with a presumption of conformity for the requirements it covers (Article 20).

Do the essential requirements apply to a quasi-machine?

Yes, those that are relevant (article 8 and section 1.1.1). Requirements that cannot be met at the time of incorporation are not covered, but the principles of security integration apply in all cases.

Sources

Updated definition as of November 13, 2026. It does not replace the reading of the official text. Find our articles on the documentation machine.

By Philippe, regulatory expert at Optima AI. Do your manuals and design documents keep up with the evolution of your machines? Optima Compliance, Our machine compliance offering helps you to write, control and maintain the documentation of your machines using your own documents.

30-minute exchange

Free, no commitment. With our customer relations manager, via video conference, on the task, the file or the machine of your choice.

Select a time slot

The booking opens in Google Calendar, in a new tab.

Would you prefer to write to us?

Optima AI SAS processes this information to answer your request (pre-contractual measures taken at your request) and to ensure commercial follow-up (our legitimate interest). It is kept for 3 years from the last contact from you. You can access it, correct it, have it deleted, and object at any time to its use for prospecting purposes by writing to contact@optimaai.fr. Privacy policy