Documentation machine

Procedure: definition, example and method for writing it (including with AI)

In this article

By Philippe, regulatory expert at Optima AI · Updated November 12, 2026

A procedure is a document that describes, step by step, how to perform a specific task at a given station: the actions, their order, the equipment, checkpoints, and safety precautions. Where a procedure says who does what and when, the procedure says how to do it. It is used to work the same way from one person to another, to train new arrivals, and to maintain the know-how of a position. Here’s what it should contain: an example with commentary, the method for writing it, and what an AI tool can contribute to it.

In short

  • A procedure answers a question: how to accomplish this task here, without making mistakes and without getting hurt? It is also called work instruction or standardized procedure.
  • The safety training organized by the employer must teach the worker «the operating procedures that are considered to affect his or her safety or that of other workers» (articles L4141-2 and R4141-13 of the Labour Code).
  • An AI tool can write a first draft based on your notes and the manual; the person who holds the position reads it back, corrects it, and validates it on the ground.

What is an operative procedure?

This is the written description, often illustrated, of the correct way to perform a task. It can be found everywhere where a task must be repeated exactly: in a workshop for a change of series, in maintenance for a part replacement, in the laboratory for sample preparation, in the quality department for a control, on a construction site for an intervention.

A good operating method has three qualities. It is precise : a step corresponds to an action, which can be verified. It is located It applies to a position, a machine, a product, not to «the company in general». It is living It changes when the machine, the product or the method change.

The word also exists in the texts. Regulation (EU) 2023/1230 on machinery, applicable on January 20, 2027, requires, as already the Directive 2006/42/EC (Annex I, section 1.7.4.2, point q), that the manufacturer’s instructions note «the operating procedure to be followed in the event of an accident or breakdown» and, if a blockage may occur, «the operating procedure to be followed to enable safe removal» (Annex III, section 1.7.4.2, point q). The Labour Code specifically requires this: for interventions that may emit asbestos fibres, the employer «draws up an operating procedure» for each process, annexed to the single risk assessment document (article R4412-145).

Workflow, procedure, work instruction, range: what difference?

These words are often used interchangeably. However, they do not answer the same question.

DocumentQuestion to which he answersExample
ProcedureWho does what, in what order, with what validations?Processing of a customer claim, from receipt to closure
Operating procedure (or work instruction)How to carry out this task, step by step, at this position?Replacing the label reel of the 2nd line labeling machine
Production rangeThrough which operations does a part pass, on which machines, with what settings?Flow, folding, punching, deburring of a sheet metal support
Instruction noticeHow to use and maintain the machine safely, according to its manufacturer?The manual supplied with the labeler
Security file at the stationWhat dangers are associated with this position, what instructions, what protective equipment?The sheet displayed near the labeler

«In practice, »work instruction« and »method of operation« mean the same document; some companies reserve the first term for short tasks. A procedure often refers to several methods of operation: the procedure says »the technician replaces the filter"; the method of operation says how.

What should a procedure manual contain?

No text mandates a single model, except in special cases such as asbestos. The following sections cover most of the needs:

  • Identification Title of the task, the relevant position or machine, reference, version, date, author and reviewer.
  • The purpose and scope What is the task for when it is applied, and when it is not applied?
  • The prerequisites : who is authorized to do it, the necessary training, and the state of the machine as expected at the start.
  • The equipment Tools, consumables, parts, individual protective equipment.
  • The steps, Numbered actions, one per line, with the verb at the head («Stop», «Check», «Tighten»).
  • The checkpoints : what is verified, with the expected value or the visible criterion.
  • Safety precautions, placed at the stage where the risk appears, not just at the top of the document.
  • The conduct to be followed if something doesn’t happen as planned: blockage, defect, alarm.
  • The related documents : manufacturer’s instructions, safety information at the station, procedure to which it is subject.

These sections overlap with what the employer must convey to those who use or maintain work equipment: «their conditions of use or maintenance,» «the instructions or guidelines concerning them, including those contained in the manufacturer’s instructions» and «the conduct to be followed in the event of foreseeable abnormal situations» (Article R4323-1 of the Labour Code). The operating procedures are one of the most direct means of conveying this information.

OPTIMA.ai image illustration showing optimization and data analysis for SEO and AI.
The sections of an operating procedure, from identification to the actions to be taken in the event of an anomaly.

Example of a commented operating procedure

The example below is fictitious, written to illustrate the method. The steps in your machine come from its instruction manual and from the experience of your position.

Procedure: changing the label reel, labeler of line 2 (version 3)
No.ActionCheckpoint / Security
1Stop the line from the control panel and wait for the entire roller to stop.The conveyor is no longer rotating. Never operate the machine while it is running.
2Open the roller shutter protector.The «protector open» light comes on.
3Remove the empty mandrel and the worn label holder.Anti-cut gloves: sharp edges on the support.
4Place the new coil, labels facing outwards.The coil reference is identical to the manufacturing order.
5Pass the support along the pattern attached to the hood.The support passes under the two return rollers.
6Close the protector, restart in step mode, make three test labels.Centered label, readable, without folds.
7Note the lot number of the coil on the production sheet.Traceability ensured.

What makes the difference: each step begins with a verb; the control is visible («the light turns on,» «center label»); the safety instruction is at step 3, where we cut off, and not buried in a general paragraph; the version is indicated, to know if we have the correct one. A photo per step is often better than one more sentence.

How to write a step-by-step operating procedure?

No text sets a revision rhythm for the operating procedures, but the training on the safety of the people who use or maintain equipment «is renewed and supplemented as often as necessary to take into account the developments of these equipment» (Article R4323-3 of the Labour Code). An operating procedure that does not follow the machine forms bad practices.

OPTIMA.ai - Writing an efficient and optimized operating procedure for productivity.
Writing a procedure: from observing the position to updating it.

Can we write a procedure manual with AI?

Yes, for the first jet. This is an instance where an AI tool provides real services, provided that you know what it does well and what it doesn’t know how to do.

What an AI tool does well

  • Transforming raw notes A description dictated at the post, scribbled notes, the transcription of an oral explanation become numbered steps, with the verb at the head.
  • Starting from existing documents : extract the instructions from the user manual that relate to the task, and indicate a forgotten precaution.
  • To standardize Same structure, same vocabulary, same level of detail from one mode of operation to another.
  • Adapt : a short version to display, a detailed version for training, a version in another language.

What he doesn't do

  • He doesn’t know your position. He doesn’t know the setting that the entire workshop does «by ear» or the machine’s trap that only the veteran knows.
  • He can write a plausible but false step. Everything related to security is verified on the machine.
  • It does not validate anything. The signature and responsibility remain within the company.

The good method boils down to one phrase: the tool prepares, your expert revises, corrects, and validates. Value does not come from the tool itself, but from the way it is used: it is the observation of the actual situation, made with the person who holds it, that gives the document its validity.

Common mistakes

  • Putting everything in a single document : procedure, operating method and safety sheet mixed together. No one reads it at the station.
  • Vague steps «Clean the machine», «check the settings». Clean what, with what, to what result?

From the operating method to the skills of the position

A procedure documents what experienced people in a position know. Optima Compliance, Our compliance machine offering brings together agents who work from your own documents. Optima Work Instructions relates to the formalization of the ranges and methods of operation, and Optima Competences Leader on the written documentation of the know-how of a workstation, based on what the person who holds it does; both are in development, with no announced date. Optima Job, in a pilot version, with support, prepares the safety sheets for the workstation based on the machine’s manual; you can try it for free here a safety sheet at the station.

To go deeper into the documents that form the basis of a procedure: What the instruction manual for a machine should contain and Machine risk analysis according to ISO 12100.

Frequently asked questions

What is the difference between a procedure and an operating method?

The procedure described a sequence of activities and responsibilities: who does what, when, with what validation. The operating mode describes how to carry out one of these activities, step by step, at a given position. A procedure often refers to several operating modes.

Is the operating procedure mandatory?

Not generally: no text requires a written procedure for each task. The employer must inform and train workers on the conditions of use of equipment and the procedures that have an impact on safety (Articles R4323-1 and R4141-13 of the Labour Code), and a written procedure makes it possible to do this and keep records of it. In some cases, it is explicitly required, such as interventions that may emit asbestos fibres (Article R4412-145).

What is the synonym for operative procedure?

We also talk about work instructions, standardized operating procedures, job instructions, or an instruction sheet. The meaning is close; the important thing is to use the same word everywhere in the company.

Who should write a procedure manual?

Ideally, the person who is proficient in the task is accompanied by someone who knows how to write clearly (methods, quality, security). The person responsible for the position or service validates it. An AI tool can prepare the first draft, but never validate it.

When should an operating procedure be updated?

With every change in machine, tool, product, or method, after an incident or near-incident, and when a trained person points out a discrepancy between the document and reality. Indicate the version and date on each copy.

Sources

Share this article LinkedIn

Free tools

Try our tools on your own documents.

Write a notice, check it, and create a safety data sheet at the workplace: our free tools, available for free, on your own documents.

See the free tools

30-minute exchange

Free, no commitment. With our customer relations manager, via video conference, on the task, the file or the machine of your choice.

Select a time slot

The booking opens in Google Calendar, in a new tab.

Would you prefer to write to us?

Optima AI SAS processes this information to answer your request (pre-contractual measures taken at your request) and to ensure commercial follow-up (our legitimate interest). It is kept for 3 years from the last contact from you. You can access it, correct it, have it deleted, and object at any time to its use for prospecting purposes by writing to contact@optimaai.fr. Privacy policy